Led support

doc/Hardware and Software Setup Instructions.md

@@ -21,6 +21,7 @@
 * Outdoor power cable, 50ft plus
 * Network router
 * Laptop/tablet
+* ws2812b LEDs
 
 ## Hardware Setup
 
@@ -44,6 +45,10 @@ Complete wiring connections between each Arduino and the Raspberry Pi.
 Note: be sure all Receiver Nodes and the Raspberry Pi are tied to a common ground; if not, the i2c messages can be corrupted.
 ![system wiring](img/D5-i2c.png)
 
+### WS2812b LED Support
+The pins in the green box is what were already used by the timer. The pins in the red box is where you connect the signal and ground from the ws2812b LEDs.  The LEDs will require a separate power source. See WS2812b LED support under Software Setup.
+![led wiring](img/GPIO.jpg)
+
 ## Software Setup
 
 ### Receiver Nodes (Arduinos)
@@ -85,6 +90,17 @@ Install web server packages, open a terminal in '/home/pi/delta5_race_timer/src/
 sudo pip install -r requirements.txt
 ```
 
+Update i2c baud rate
+```
+sudo nano /boot/config.txt
+```
+add the following line:
+```
+dtparam=i2c_baudrate=75000
+```
+Save and exit the file with Ctrl-x
+
+
 ## Starting the System
 
 The following instructions will start the Delta5 Race Timer web server on the raspberry pi allowing full control and configuration of the system to run races and save lap times.  
@@ -128,3 +144,48 @@ sudo systemctl daemon-reload
 sudo systemctl enable delta5.service
 sudo reboot
 ```
+### WS2812b LED Support
+The ws2812b controls are provided by the following project:
+/~https://github.com/jgarff/rpi_ws281x
+
+Perform an update and install the dependencies:
+```
+sudo apt-get update
+sudo apt-get install build-essential python-dev git scons swig
+```
+
+Clone the repository onto the Pi and initiate Scons:
+```
+sudo git clone /~https://github.com/jgarff/rpi_ws281x.git
+cd rpi_ws281x
+sudo scons
+```
+
+Install the Python library:
+```
+cd python
+sudo python setup.py install
+```
+
+Modify the config.txt file
+```
+sudo nano /boot/config.txt
+```
+add the following to the config.txt file
+```
+core_freq=250
+```
+Configure the Raspberry Pi to enable SPI
+```
+sudo raspi-config
+```
+Select 5 Interfacing Options
+
+Select P4 SPI
+
+and enable SPI
+
+Reboot the Raspberry Pi
+```
+sudo reboot
+```

src/delta5node/delta5node.ino

@@ -29,7 +29,7 @@
 // Node Setup -- Set the i2c address here
 // Node 1 = 8, Node 2 = 10, Node 3 = 12, Node 4 = 14
 // Node 5 = 16, Node 6 = 18, Node 7 = 20, Node 8 = 22
-#define i2cSlaveAddress 8
+#define i2cSlaveAddress 20
 
 const int slaveSelectPin = 10; // Setup data pins for rx5808 comms
 const int spiDataPin = 11;
@@ -99,6 +99,22 @@ uint8_t volatile ioBuffer[32]; // Data array for sending over i2c, up to 32 byte
 int ioBufferSize = 0;
 int ioBufferIndex = 0;
 
+// Define vtx frequencies in mhz and their hex code for setting the rx5808 module
+int vtxFreqTable[] = {
+  5865, 5845, 5825, 5805, 5785, 5765, 5745, 5725, // Band A
+  5733, 5752, 5771, 5790, 5809, 5828, 5847, 5866, // Band B
+  5705, 5685, 5665, 5645, 5885, 5905, 5925, 5945, // Band E
+  5740, 5760, 5780, 5800, 5820, 5840, 5860, 5880, // Band F
+  5658, 5695, 5732, 5769, 5806, 5843, 5880, 5917  // Band C / Raceband
+};
+uint16_t vtxHexTable[] = {
+  0x2A05, 0x299B, 0x2991, 0x2987, 0x291D, 0x2913, 0x2909, 0x289F, // Band A
+  0x2903, 0x290C, 0x2916, 0x291F, 0x2989, 0x2992, 0x299C, 0x2A05, // Band B
+  0x2895, 0x288B, 0x2881, 0x2817, 0x2A0F, 0x2A19, 0x2A83, 0x2A8D, // Band E
+  0x2906, 0x2910, 0x291A, 0x2984, 0x298E, 0x2998, 0x2A02, 0x2A0C, // Band F
+  0x281D, 0x288F, 0x2902, 0x2914, 0x2987, 0x2999, 0x2A0C, 0x2A1E  // Band C / Raceband
+};
+
 // Defines for fast ADC reads
 #define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
 #define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
@@ -170,21 +186,20 @@ void SERIAL_ENABLE_HIGH() {
 	delayMicroseconds(100);
 }
 
-// Calculate rx5808 register hex value for given frequency in MHz
-uint16_t freqMhzToRegVal(uint16_t freqInMhz) {
-  uint16_t tf, N, A;
-  tf = (freqInMhz - 479) / 2;
-  N = tf / 32;
-  A = tf % 32;
-  return (N<<7) + A;
-}
-
 // Set the frequency given on the rx5808 module
 void setRxModule(int frequency) {
 	uint8_t i; // Used in the for loops
 
-	// Get the hex value to send to the rx module
-	uint16_t vtxHex = freqMhzToRegVal(frequency);
+	uint8_t index; // Find the index in the frequency lookup table
+	for (i = 0; i < sizeof(vtxFreqTable); i++) {
+		if (frequency == vtxFreqTable[i]) {
+			index = i;
+			break;
+		}
+	}
+
+	uint16_t vtxHex; // Get the hex value to send to the rx module
+	vtxHex = vtxHexTable[index];
 
 	// bit bash out 25 bits of data / Order: A0-3, !R/W, D0-D19 / A0=0, A1=0, A2=0, A3=1, RW=0, D0-19=0
 	SERIAL_ENABLE_HIGH();

src/delta5server/server.py

@@ -36,6 +36,87 @@
 PROGRAM_START = datetime.now()
 RACE_START = datetime.now() # Updated on race start commands
 
+# LED Code
+import time
+from neopixel import *
+
+import signal
+def signal_handler(signal, frame):
+        colorWipe(strip, Color(0,0,0))
+        sys.exit(0)
+
+# LED strip configuration:
+LED_COUNT      = 150      # Number of LED pixels.
+#LED_PIN        = 18      # GPIO pin connected to the pixels (18 uses PWM!).
+LED_PIN        = 10      # GPIO pin connected to the pixels (10 uses SPI /dev/spidev0.0).
+LED_FREQ_HZ    = 800000  # LED signal frequency in hertz (usually 800khz)
+LED_DMA        = 10      # DMA channel to use for generating signal (try 10)
+LED_BRIGHTNESS = 255     # Set to 0 for darkest and 255 for brightest
+LED_INVERT     = False   # True to invert the signal (when using NPN transistor level shift)
+LED_CHANNEL    = 0       # set to '1' for GPIOs 13, 19, 41, 45 or 53
+LED_STRIP      = ws.WS2811_STRIP_GRB   # Strip type and colour ordering
+
+# LED one color ON/OFF
+def onoff(strip, color):
+	for i in range(strip.numPixels()):
+		strip.setPixelColor(i, color)
+	strip.show()
+
+def theaterChase(strip, color, wait_ms=50, iterations=5):
+    """Movie theater light style chaser animation."""
+    for j in range(iterations):
+        for q in range(3):
+            for i in range(0, strip.numPixels(), 3):
+                strip.setPixelColor(i+q, color)
+            strip.show()
+            time.sleep(wait_ms/1000.0)
+            for i in range(0, strip.numPixels(), 3):
+                strip.setPixelColor(i+q, 0)
+
+def wheel(pos):
+    """Generate rainbow colors across 0-255 positions."""
+    if pos < 85:
+        return Color(pos * 3, 255 - pos * 3, 0)
+    elif pos < 170:
+        pos -= 85
+        return Color(255 - pos * 3, 0, pos * 3)
+    else:
+        pos -= 170
+        return Color(0, pos * 3, 255 - pos * 3)
+
+def rainbow(strip, wait_ms=2, iterations=1):
+    """Draw rainbow that fades across all pixels at once."""
+    for j in range(256*iterations):
+        for i in range(strip.numPixels()):
+            strip.setPixelColor(i, wheel((i+j) & 255))
+        strip.show()
+        time.sleep(wait_ms/1000.0)
+
+def rainbowCycle(strip, wait_ms=2, iterations=1):
+    """Draw rainbow that uniformly distributes itself across all pixels."""
+    for j in range(256*iterations):
+        for i in range(strip.numPixels()):
+            strip.setPixelColor(i, wheel((int(i * 256 / strip.numPixels()) + j) & 255))
+        strip.show()
+        time.sleep(wait_ms/1000.0)
+
+def theaterChaseRainbow(strip, wait_ms=25):
+    """Rainbow movie theater light style chaser animation."""
+    for j in range(256):
+        for q in range(3):
+            for i in range(0, strip.numPixels(), 3):
+                strip.setPixelColor(i+q, wheel((i+j) % 255))
+            strip.show()
+            time.sleep(wait_ms/1000.0)
+            for i in range(0, strip.numPixels(), 3):
+                strip.setPixelColor(i+q, 0)
+
+# Create NeoPixel object with appropriate configuration.
+strip = Adafruit_NeoPixel(LED_COUNT, LED_PIN, LED_FREQ_HZ, LED_DMA, LED_INVERT, LED_BRIGHTNESS, LED_CHANNEL, LED_STRIP)
+# Intialize the library (must be called once before other functions).
+strip.begin()
+
+
 #
 # Database Models
 #
@@ -521,12 +602,16 @@ def on_start_race():
     '''Starts the race and the timer counting up, no defined finish.'''
     start_race()
     SOCKET_IO.emit('start_timer') # Loop back to race page to start the timer counting up
+    time.sleep(1)
+    onoff(strip, Color(0,255,0)) #GREEN ON
 
 @SOCKET_IO.on('start_race_2min')
 def on_start_race_2min():
     '''Starts the race with a two minute countdown clock.'''
     start_race()
     SOCKET_IO.emit('start_timer_2min') # Loop back to race page to start a 2 min countdown
+    time.sleep(1)
+    onoff(strip, Color(0,255,0)) #GREEN ON
 
 def start_race():
     '''Common race start events.'''
@@ -549,6 +634,7 @@ def on_race_status():
     SOCKET_IO.emit('stop_timer') # Loop back to race page to start the timer counting up
     server_log('Race stopped')
     emit_race_status() # Race page, to set race button states
+    onoff(strip, Color(255,0,0)) #RED ON
 
 @SOCKET_IO.on('save_laps')
 def on_save_laps():
@@ -623,6 +709,34 @@ def on_simulate_lap(data):
     server_log('Simulated lap: Node {0}'.format(node_index))
     INTERFACE.intf_simulate_lap(node_index)
 
+@SOCKET_IO.on('LED_solid')
+def on_LED_solid(data):
+    '''LED Solid Color'''
+    led_red = data['red']
+    led_green = data['green']
+    led_blue = data['blue']
+    onoff(strip, Color(led_red,led_green,led_blue))
+
+@SOCKET_IO.on('LED_chase')
+def on_LED_chase(data):
+    '''LED Solid Color'''
+    led_red = data['red']
+    led_green = data['green']
+    led_blue = data['blue']
+    theaterChase(strip, Color(led_red,led_green,led_blue))
+
+@SOCKET_IO.on('LED_RB')
+def on_LED_RB():
+    rainbow(strip) #Rainbow
+
+@SOCKET_IO.on('LED_RBCYCLE')
+def on_LED_RBCYCLE():
+    rainbowCycle(strip) #Rainbow Cycle
+
+@SOCKET_IO.on('LED_RBCHASE')
+def on_LED_RBCHASE():
+    theaterChaseRainbow(strip) #Rainbow Chase
+
 # Socket io emit functions
 
 def emit_race_status():
@@ -871,6 +985,22 @@ def pass_record_callback(node, ms_since_lap):
         emit_leaderboard() # Updates leaderboard
         if lap_id > 0: 
             emit_phonetic_data(pilot_id, lap_id, lap_time) # Sends phonetic data to be spoken
+        if node.index==0:
+            theaterChase(strip, Color(0,0,255))  #BLUE theater chase
+        elif node.index==1:
+            theaterChase(strip, Color(255,50,0)) #ORANGE theater chase
+        elif node.index==2:
+            theaterChase(strip, Color(255,0,60)) #PINK theater chase
+        elif node.index==3:
+            theaterChase(strip, Color(150,0,255)) #PURPLE theater chase
+        elif node.index==4:
+            theaterChase(strip, Color(250,210,0)) #YELLOW theater chase
+        elif node.index==5:
+            theaterChase(strip, Color(0,255,255)) #CYAN theater chase
+        elif node.index==6:
+            theaterChase(strip, Color(0,255,0)) #GREEN theater chase
+        elif node.index==7:
+            theaterChase(strip, Color(255,0,0)) #RED theater chase
 
 INTERFACE.pass_record_callback = pass_record_callback